Guides · Room requirements by launch monitor
How Much Room Does a SkyTrak Golf Simulator Need?
Published · Updated
SkyTrak's basic hitting-bay guide lists a minimum of 12 feet long, 10 feet wide, and 9 feet high, but a Studio package can need a larger room. Its current planning page gives the Studio10 a minimum room size of 11 feet wide, 16 feet deep, and 9 feet high. Use the guidance for your exact enclosure, then check your swing from the finished mat.
Minimum and recommended
SkyTrak's basic hitting-bay guide lists 12 feet long, 10 feet wide, and a 9-foot net height as minimum dimensions. It recommends 15 feet long, 15 feet wide, and 10 feet high when space allows. The guide allows about 10 feet for hitting plus 1–2 feet of ball clearance, and says height depends on the golfer. These are general planning figures, not a guarantee that your driver swing will fit. SkyTrak hitting-bay requirements
Studio sizes
An enclosure's depth is only part of the room depth. SkyTrak's current planning page lists these minimum and ideal room dimensions, in width × depth × height order. All values are in feet:
| Studio | Minimum room W × D × H (ft) | Ideal room W × D × H (ft) |
|---|---|---|
| Studio10 | 11 × 16 × 9 | 12–14 × 17–20 × 9–10 |
| Studio12 | 13 × 16 × 9 | 14–16 × 17–20 × 9–10 |
| Studio13 Deep | 14 × 17 × 10.5 | 15–17 × 18–20 × 11+ |
The Studio10 and Studio12 enclosures are 5 feet 4 inches deep; the Studio13 Deep is 10 feet deep. The remaining room accommodates tee placement, the swing, and clearance around the structure. Confirm the package's installation instructions before ordering. SkyTrak Studio planning dimensions
Cameras at the ball
SkyTrak sits beside the ball, so you don't need a rear tracking lane for the monitor. A shorter room that couldn't take a rear-mounted radar monitor may take a SkyTrak. The screen, enclosure, and golfer still need their own space. SkyTrak layout guidance
Level with the hitting surface
SkyTrak's alignment guide says to set the height so the bottom of the unit is even with the top of your hitting surface, then zero out tilt and roll with the adjustable feet on the protective case. On a thick mat, you may need a stable platform under the unit. SkyTrak alignment guide
For the standard starting ball position, put the ball or the base of the tee on the red laser dot. SkyTrak's tips also describe small position adjustments for shots that aren't captured reliably. SkyTrak tips for use
Aiming the unit
The launch monitor should sit parallel to the target line. A mat that creeps across the floor can leave the unit looking square while the target line has moved.
SkyTrak suggests a tape measure, laser, or other long straight line to check that the line from the red dot to your intended screen or net target is parallel to the unit. Then verify that shots hit along that line start straight in the app. Repeat the alignment check whenever the mat, launch monitor, or hitting strip moves. SkyTrak alignment steps
Nine feet for whom?
A 9-foot ceiling may suit one golfer and restrict another. Start with slow practice swings with your driver from the actual mat, accounting for lights, beams, and garage-door hardware. Progress only when there's clear space through the whole swing.
Width works the same way. If a left-handed player shares the room, check both swings at the intended hitting positions. A centered ball position can need more side clearance than an offset setup for one player.
Check the room before choosing a package
Use the room size calculator to record your usable dimensions and compare layout options. Measure below beams and garage-door tracks, and include the finished mat height. The calculator does not certify swing clearance or replace the exact enclosure's installation requirements.
Once the room fits, compare simulator packages and enclosures with the table above. Check the selected bundle's contents: the monitor, projector, mat, and computer may be included or sold separately.